GLM75IG【PDF 1/2 页】PWR SPLY MED SWITCHER 75W MULTI

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录227

[1页]2页

GLOBAL PERFORMANCE SWITCHERS

GLC75 Commercial/GLM75 Medical

75 Watt Multiple Output Global Performance Switchers

FEATURES:

? Cost-effective multiple output power source

? Universal input 90-264 Vac

? 7.00”x 4.25”x 1.30” (Meets 1U height)

? 2-year warranty

? Conducted EMI exceeds FCC Class B and CISPR 22

Class B (Commercial models) and CISPR 11 Class B

(Medical models)

? Complies with EN61000-3-2 Class A

? Also available in single output versions

? Commercial UL1950 3rd Edition, CSA22.2 No. 950 and

EN60950-1 approvals

? Medical Approved to UL2601-1,

CSA22.2 No. 601.1-M90, and IEC/EN60601-1

? RoHS Compliant Model Available (G suffix)

SPECIFICATIONS

Ac Input

90-264 Vac, 47-63 Hz single phase.

Input Current

Maximum input current at 120 Vac, 60 Hz with full rated output load not to

exceed 2.3 A.

Output Power

Normal continuous output power is 75 W for unrestricted natural convection

cooling or 110 W with 26 cfm airflow. During peak load conditions output

regulation may exceed total regulation and noise limits.

Output Regulation

Measured by ±40% load change from 60% rated load with all other outputs

at 60% rated load and input voltage change from minimum to maximum rat-

ings. Output #1 requires 1A minimum load for proper regulation of other

outputs. Initial set tolerance is measured with all outputs at 60% of full rated

load. Output #2 requires 0.5A minimum load for proper regulation.

Overload Protection

Factory set to begin power limiting at approximately 120 W. Fully protected

against short circuit and output overload. Short circuit protection is cycling

type power limit.

Output Noise

0.5% rms, 1% pk-pk, 20 MHz bandwidth, differential mode. Measured with

noise probe directly across output terminals of the power supply.

Transient Response

Main Output: 500μSec typical response time for return to within 0.5% of final

value for a 50% load step change, ?i/?t<0.2A/μSec. Maximum voltage devia-

tion is 3.5%.

Overvoltage Protection

Built in on V1 with firing point set per table. OVP firing reduces output #1 and

#2 to less than 50% of nominal voltage in 50 ms.

Voltage Adjust

Factory set on standard unit; however, optional potentiometer (“-V” suffix)

adjusts voltage from 4.7 V to OVP point (6.2 V nominal) on the +5 V output.

Note: Output #1 must not be more than 1% below nominal to achieve full

output voltage range on Output #2. Output regulation limits in some models

may be exceeded when the main output is adjusted beyond +1% of nominal

voltage. High voltage settings may degrade the reliability of the unit due to

excessive power dissipation in some outputs.

Efficiency

68% -78% depending on model and load distribution.

Input Protection

Internal ac fuse provided on all units. Designed to blow only if a catastrophic

failure occurs in the unit.

Inrush Current

Inrush limited by internal thermistors. Inrush at 240 Vac, averaged over the first ac

half-cycle under cold start conditions will not exceed 37 A.

Hold Up Time

20 ms minimum from loss of ac input power at full load, nominal line (120 Vac).

Temperature Coefficient

0.03%/°C typical on all outputs.

Power Fail

A standard TTL or CMOS compatible output goes low (< 0.5 V) 5ms before output

voltage drops more than 4% below nominal voltage upon loss of ac power. Signal

is factory set to trip on 84 to 94 Vac brown-out depending upon incoming line

impedance and distortion. Other settings are available through adjustment of

built-in potentiometer (consult factory for assistance). Output will stay low for 20

ms minimum.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the following emissions requirements:

EMI SPECIFICATIONS COMPLIANCE LEVEL

Conducted Emissions GLC75 EN55022 Class B; FCC Class B

Conducted Emissions GLM75 EN55011 Class B: FCC Class B

Static Discharge EN61000-4-2, 6 kV contact, 8 kV air

RF Field Susceptibility EN61000-4-3, 3 V/meter

Fast Transients/Bursts EN61000-4-4, 2 kV, 5 kHz

Surge Susceptibility EN61000-4-5, 1 kV diff., 2 kV com.

Line Frequency Harmonics EN61000-3-2 Class A

Commercial Safety

All GLC models are approved to UL1950 3rd Edition, CSA22.2 No. 950, and

EN60950-1.

Medical Leakage Current

70 μA 264 V @ 50 Hz (normal conditions).

Medical Safety

GLM models are approved to UL2601-1, CSA22.2 No. 601.1M90, IEC/EN60601-1. CB

Report available.

All specifications are typical at nominal input, full load at 25 O C unless otherwise stated

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式